![]() The SecuriCode has existed this long partly due to its simplicity and customer approval. Just store them somewhere unseen for added security. You can also keep your phone and valuables inside the truck if you don’t want to carry them or are afraid of losing them. Lock them inside your car and retrieve them by entering your code. With the SecuriCode, you don’t have to worry about losing your keys if you’re fond of outdoor activities. Is the Ford Keypad Reliable?įord’s SecuriCode keypad is as reliable as they come.įirst released in 1980, the feature is synonymous with Ford vehicles, with its competitors still failing to make a better alternative 42 years later. Your code will pop up on the instrument panel for a few seconds. Insert your second key and press the START/STOP button. Press the START/STOP button again, then take out the key. Once your key is in the slot, press the START/STOP button once, then wait five seconds. If you can’t find your backup slot, go to the “Starting and Stopping the Engine” section in your owner’s manual.įind the instructions on “Keyless Starting” and read through “If you are unable to start your vehicle.” To retrieve your code, put the first key in the backup slot (where you place your key fob when you can’t start the truck). If you don’t have them, head to the nearest Ford dealership or contact your dealer. Like the Smart Key process, you’ll need the two Intelligent Access Keys that came with your vehicle. Proof of VIN includes the current Vehicle Registration, Vehicle Title, or Bill of Sale.įees may apply during the process. ![]() Proof of your VIN (Vehicle Identification Number) and name.The attendant will ask for your personal and vehicle information, so make sure to carry: If you only have one key, you’ll have to get your code from the nearest Ford dealership. It displays for only a few seconds, so have a pen and paper (or phone camera) ready. Your factory-set code will pop up on the instrument panel above the steering wheel. Switch off the truck, take out the key, and turn on the ignition with the second key. Start by turning on the ignition with one key and letting the vehicle run for a few seconds. To retrieve the factory-set code, you need both keys that came with your truck. The Smart Key doubles up as your ignition key. You can use the Smart Key or the Intelligent Access key. The steps to retrieve your factory-set entry code depend on your key type. How To Retrieve the Factory-Set Entry Code Go to “Door Keypad Code,” enter your factory-set entry code, and click “Add” to set up your new code.ĭon’t forget that you can add up to five personal entry codes. SYNC with MyFord TouchĬlick the Gear icon on your screen and tap “Vehicle.” Go to “Door Keypad Code” and key in your pre-set entry code.Ĭlick “Add” and set up your new entry code.ĭon’t use numbers in a sequence or five of the same number. Navigate to “Settings” on your SYNC screen and click “Vehicle tile.” Similar to using the keypad, you need your factory-set code before you can do the following: SYNC 3 The Ford SecuriCode allows you to program your entry code using SYNC 3 or SYNC® with MyFord Touch. How To Program a Personal Entry Code Using SYNC You unlock your truck using Intelligent Access.You unlock your truck using the remote control.When you trigger the anti-scan, the keypad lamp flashes, then locks the keypad for one minute before you can try again. Keep in mind that your new code doesn’t erase the factory code.Īlso, ensure to enter the correct code when unlocking your car, as the keypad goes into an anti-scan mode after seven wrong tries. Do not base it on a single number, e.g., 33333.Enter your new code (input each number in five-second intervals).Press 1/2 on the keypad within five seconds.Key in the five-digit factory-set code.(Don’t worry if you’ve lost your card, there’s a way to retrieve your code, discussed below). To start, find the pre-set security code on your owner’s wallet card in the glove compartment. You can program up to five personal entry codes. Though the F-150 (and other Ford vehicles) come with a pre-set security code, Ford allows you to program your own. How To Program a Personal Entry Code on the F-150 Keypad If you enter them too quickly, the door won’t open. When you want to open your trunk, enter the factory-set five-digit code or your personal code, then press and hold 5/6. To unlock your truck, enter the factory-set five-digit code or your personal code, then press and hold 3/4. To lock your F-150 with your keypad, ensure the driver’s side door is closed and then press and hold 7/8 and 9/0 simultaneously. The keypad might seem hard to navigate if you just got your truck. The SecuriCode keypad is a convenient and keyless way to lock and unlock your F-150 using the keypad on your door handle.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |